IMLAC LOADING PROCEDURE:

1.Turn  OFF  the  IMLAC's  main power switch at the left rear corner.   (It
  must remain off for at least 6 seconds.)

2.Switch  the "Start At" switch (at right rear of IMLAC) to "40".   This is
  the starting address of the IMLAC's hard wired bootstrap loader.

3.If  the  power switch has been off for at least 6 seconds, then switch it
  back on.  The RUN light (little  red  light  beside  "Start  At"  switch)
  should  come  on  and stay on.  If it does not stay on, start the Loading
  Procedure over again.

4.On another (logged-in) console or teletype, type "R FIXIML".  This may be
  done from an adjacent IMLAC, a teletype in Pine Hall or you may call  the
  A.I.Project on extension 4971 and ask any co-operative sounding person to
  run FIXIML for you.  After this program is started, it will  ask  "RELOAD
  WHICH  IMLAC?".   The correct response will be "16" or "17"--depending on
  which of these Line numbers appears on the black dymo label  attached  to
  the  lower right corner of the keyboard for the particular IMLAC you want
  to load.  After you  respond  with  one  of  these  numbers  followed  by
  "RETURN",  program FIXIML will say "TYPE IN YOUR PPN." followed by "#" on
  the next line.   At this point you should type your PPN exactly as if you
  were  logging  in.   (You must separate your project and your programmmer
  name with a comma.) If the IMLAC is logged in under someone  else's  PPN,
  then  FIXIML  will not work unless you give the PPN under which the IMLAC
  is logged in.  If the IMLAC is not logged in at  all,  FIXIML  will  work
  okay.    If there is no problem, then FIXIML will say "START THE IMLAC AT
  40; THEN HIT <CR>".  If you did steps 1 to 3 above  correctly,  then  you
  have  already  started  the  IMLAC at 40, so just hit the carriage-return
  key.  If you haven't done steps 1 to 3 yet, do  them  now  and  then  hit
  carriage-return  and  come back to here.  When you type <CR>, FIXIML will
  say "SENDING LOADER" followed quickly by "LOADING RIP".    Then  look  to
  see  that  the  Run  light  is still on (unless you are not where you can
  observe it).  If it is not on, start the Loading  Procedure  over  again.
  If it is on, or if you aren't near it, wait approximately 2 or 3 minutes,
  after which, program FIXIML should type out "RIP  LOADED!",  "EXIT",  and
  "↑C".     At  this  point  loading  should  be complete.   If loading was
  successful, a curser should appear  in  the  upper  left  corner  of  the
  IMLAC's  display  screen.  If it does not, hit the CALL key on the IMLAC;
  if still nothing happens, then turn the IMLAC off for at least 6 seconds,
  set  the  "START  AT"  switch to "100" and (after the 6 seconds) turn the
  IMLAC back on again.   Then hit CALL again to see if  the  IMLAC  is  now
  working.    If  it  is, then you need read no further.  If not, the whole
  Loading Procedure must be started over again (see the notes below first).

     NOTES: 1.Patience and persistence are valuable assets.   It  may  take
              several tries before the IMLAC is successfully loaded.

            2.If  the  IMLAC  cannot  be loaded after trying several times,
              enter a note in the IMLAC Trouble Log describing the problem.
              Also  please  send a note to Dave Emerson by using the system
              SEND command by typing "SEND DWE"  (on  a  working  console).
              The SEND program will tell you how to use it.